I'm trying to configure my Sipura2100 to use VoipBuster - It doesnt seem to
work although the software is fine.
I set stun server to stun.voipbuster.com and resgistrar to
sip.voipbuster.com (tried also voipbuster.com and stun.voipbuster.com) with
my login credentials - no go -
Also how do I go about having a different incoming supplier on this device?
do I need the latest firmware?.
In message of Fri, 16 Sep 2005, John Smith writes
>Hi,
>
>I'm trying to configure my Sipura2100 to use VoipBuster - It doesnt seem to
>work although the software is fine.
>I set stun server to stun.voipbuster.com and resgistrar to
>sip.voipbuster.com (tried also voipbuster.com and stun.voipbuster.com) with
>my login credentials - no go -
>Also how do I go about having a different incoming supplier on this device?
>do I need the latest firmware?.
>
Can't help with SPA2100 but I use an SPA3000 and that works OK but I
don't use it as an account with VoIPBuster only as a Gateway.
sip.voipbuster.com is OK. You can use any STUN server - in fact I use
stun.sipgate.net:10000 because I've never changed it from when I started
experimenting. Works fine.
>Hi,
>
>I'm trying to configure my Sipura2100 to use VoipBuster - It doesnt seem to
>work although the software is fine.
Just one comment which might be helpful. Even though your equipment
may be set up perfectly voipbuster doesn't always work. I have
programmed 'speed dials' into my SPA-3000 dial plan, #1, #2 etc. They
all go through voipbuster. Sometimes the connection is immediate,
sometimes a short delay and then connection, sometimes I get an
unobtainable tone and other times I get just silence. I usually reckon
that if there is no connection within 5 seconds it ain't going to
happen. It is then worth trying again but sometimes voipbuster is too
busy to cope, I think, and it is best to try at a less busy time.
On my system I have a 'warm line' set. If I start dialling within 4
seconds calls go through voipbuster but if I simply lift the handset
and wait calls get routed to another operator.
>I set stun server to stun.voipbuster.com and resgistrar to
>sip.voipbuster.com (tried also voipbuster.com and stun.voipbuster.com) with
>my login credentials - no go -
>Also how do I go about having a different incoming supplier on this device?
>do I need the latest firmware?.
I have the SPA-3000 so it might be different but , under the 'Line 1'
tab, is 'Gateway Accounts'. Just set up your alternative providers
there and then access them via your dial plan referring to gw1, gw2
etc.
"John Smith" <John@hotmail.com> wrote in message
news:94vWe.109501$G8.5455@text.news.blueyonder.co. uk...
> Hi,
>
> I'm trying to configure my Sipura2100 to use VoipBuster - It doesnt seem
> to work although the software is fine.
> I set stun server to stun.voipbuster.com and resgistrar to
> sip.voipbuster.com (tried also voipbuster.com and stun.voipbuster.com)
> with my login credentials - no go -
> Also how do I go about having a different incoming supplier on this
> device? do I need the latest firmware?.
No great help, but on my ATA I can only make 1 minute calls before getting
cutoff for not having credit in my account. I have two accounts, both with
credit, that work fine with the voipbuster software, but it looks like the
SIP stuff via the ATA is not somehow correlatating to my account.
> I have the SPA-3000 so it might be different but , under the 'Line 1'
> tab, is 'Gateway Accounts'. Just set up your alternative providers
> there and then access them via your dial plan referring to gw1, gw2
> etc.
>
> Remove 'no_spam_' from email address.
Hi, I just discovered voipbuster.com and seems interesting with their "super
deal"
I am currently using voipfone.co.uk with a SPA-3000
>
>> I have the SPA-3000 so it might be different but , under the 'Line 1'
>> tab, is 'Gateway Accounts'. Just set up your alternative providers
>> there and then access them via your dial plan referring to gw1, gw2
>> etc.
>>
>> Remove 'no_spam_' from email address.
>
>Hi, I just discovered voipbuster.com and seems interesting with their "super
>deal"
>I am currently using voipfone.co.uk with a SPA-3000
>
>I just signed up an account with voipbuster.com
>
>I tried to comfigure my SPA3000 as :
>
>gateway1 : sip.voipbuster.com
>GW1Auth : (my voipbuster username)
>GW1 NAT : no
>GW1 pawwrd : (my voipbuster password)
I have NAT on but not sure if it makes any difference.
You have not mentioned STUN. Go to the SIP tab and enter
'stun.voipbuster.com'
for 'STUN server'
I have 'YES' for all under 'NAT Support Parameters'
>
>In my dial plan : <9,:>x.<:@gw1>
Your dial plan is OK. While you are testing you might find it more
useful to use something like:-
<#1,:00441234567890><:@gw1>
That way a number is dialled for you and you simply have to press #1
to call it and route through voipbuster. It is a good way of entering
'speed dials'. Alternatively you could do a 'hot line'.
P0 <:00441234567890><:@gw1>
That will dial the number for you just by taking the handset 'off
hook'.
Do remember my earlier posting. Voipbuster isn't always accesible. You
might get a good set up and it still doesn't work. Try up to 5 times
and then at another time. If voipbuster is busy you might not get in.
Sometimes though connection is immediate.
>
>I didn't put any money on my account, so I should be able to make a test
>phone call, even < 1min ?
Yes
>
>- Do you think that the config is OK ?
>- Except some FAQ, is there a way to contact the tech support ??
Don't think there is one. I dont think you can offer calls at zero
price and run a tech support as well.
>
Hope this helps!
In message of Sat, 17 Sep 2005, Stephane M writes
>
>> I have the SPA-3000 so it might be different but , under the 'Line 1'
>> tab, is 'Gateway Accounts'. Just set up your alternative providers
>> there and then access them via your dial plan referring to gw1, gw2
>> etc.
>>
>> Remove 'no_spam_' from email address.
>
>Hi, I just discovered voipbuster.com and seems interesting with their "super
>deal"
>I am currently using voipfone.co.uk with a SPA-3000
>
>I just signed up an account with voipbuster.com
>
>I tried to comfigure my SPA3000 as :
>
>gateway1 : sip.voipbuster.com
>GW1Auth : (my voipbuster username)
>GW1 NAT : no
>GW1 pawwrd : (my voipbuster password)
>
As I've said in another thread on this topic, my settings for the
SPA3000 are:
"David Floyd" <david@floyd.org.uk> wrote in message
news:RKhc34AD6ALDFwtn@127.0.0.1...
> In message of Sat, 17 Sep 2005, Stephane M writes
> >
> >> I have the SPA-3000 so it might be different but , under the 'Line 1'
> >> tab, is 'Gateway Accounts'. Just set up your alternative providers
> >> there and then access them via your dial plan referring to gw1, gw2
> >> etc.
> >>
> >> Remove 'no_spam_' from email address.
> >
> >Hi, I just discovered voipbuster.com and seems interesting with their
"super
> >deal"
> >I am currently using voipfone.co.uk with a SPA-3000
> >
> >I just signed up an account with voipbuster.com
> >
> >I tried to comfigure my SPA3000 as :
> >
> >gateway1 : sip.voipbuster.com
> >GW1Auth : (my voipbuster username)
> >GW1 NAT : no
> >GW1 pawwrd : (my voipbuster password)
> >
>
> As I've said in another thread on this topic, my settings for the
> SPA3000 are:
>
> Gateway 4: <UserID>@sip.voipbuster.com
> GW4 Auth ID: <UserID>
> GR4 NAT Mapping Enable: yes
> GW4 Password: <password>
>
> This works for me with JustDialVoIP set up on Line 1
>
> David
VoipBuster accepting SIP connections? 
Linear Mode
